J Mount for Starlink: Top 4 Recommendations And Installation Guide

Immediately after getting your Starlink kit, your next accessory should be a J Mount for Starlink. J mounts are one of the most versatile and adjustable mounts that work with 1st and 2nd generation Starlink …

Satellite on a J-mount

Immediately after getting your Starlink kit, your next accessory should be a J Mount for Starlink.

J mounts are one of the most versatile and adjustable mounts that work with 1st and 2nd generation Starlink dishes. 

Your Starlink dish needs a mount that can withstand erratic weather.

Still, you might need minor adjustments to get a snug fit while mounting a J mount for Starlink.

Aftermarket J mounts give you some wiggle room if you get a Starlink mast that’s not an exact fit. 

 We’ll give you four J mount recommendations, the right questions to ask when you want to buy, and how to install them.

Table of Contents

J mount on a roof’s siding

J mount on a roof’s siding

J mounts are one of the many mounts you can use to hoist a satellite dish to your home’s wall, roof, fascia, or soffit. 

Usually, a J mount is mounted on a heavy base. However, the most crucial part is the top end, where you insert the end of your dish, in this case, Starlink dish. 

The pipe’s J shape is helpful when it comes to attaching the mount to a house. It allows you to stick the mount on many parts of a house and use different mount adapters or other mounts like a volcano mount. 

Most aftermarket J mounts have a larger diameter to accommodate the Starlink mast. 

Therefore, they have pre-drilled holes where you can attach screws and secure the Starlink satellite mast. 

These four inclusions have been tried and tested. They come in high-grade material and work best with both generations of Starlink dishes.

Phillips has a long history of reliable products globally. We recommend the Phillips Universal J Mount because of its guaranteed technical support and lifetime replacement pledge.

The mount base is adjustable, so you can swing the lower part of the mount up or down before locking in position.

 Furthermore, the base plate is flat, so you can install it on wall siding or the roof on a flat surface. 

The Phillips Universal J Mount is 17.5 inches of high-quality steel with exterior weatherproofing. 

That length is enough to get you a clear view of the skies when installing a Starlink dish. 

This mount feels lightweight at slightly below 2 lbs. You won’t struggle during installation.

Finally, it comes pre-drilled with three holes to give you enough clearance not to damage the dish. The package also includes all the washers, nuts, and bolts you need for fitting. 

The Winegard DS2000A J Mount should be one of the mounts to consider for your Starlink dish. 

The entire Winegard lineup of mounts offers excellent alternatives, such as DS-3000, for longer reach.  

This 22-inch mount is perfect for outdoor applications for satellites, antennas, and Wi-Fi extenders. It has extra hardware, such as U-bolts, for secure Starlink installation. 

It has a heavy solid mounting plate you can install on wall siding or even poles. 

The wide mounting plate redistributes weight if there’s a heavy wind that might compromise the mount. 

You can also adjust the positioning of the pole on the mounting plate. It has lag bolts you can use to fit on a soffit. 

The diameter works well with the 2nd generation Starlink and needs only minor adjustments to be a snug fit. 

Finally, its e-coating makes it the perfect outdoor Starlink mounting accessory. The coating protects it against adverse weather elements. 

Best For Tough Weather: Proxicast Pro-Grade J-Max

Although a bit pricier than the last two, the Proxicast Pro-grade J-Max J mount is exactly what you need to steady your Starlink in harsh weather. 

You can go for the 18-inch option or the 36-inch J-Max XL mount if you want extra clearance. Also, it is made out of rust-proof aluminum.

 Although the Starlink dish is not heavy, the alternative 304 stainless steel option can provide extra stability in heavy wind areas or against heavy snow. 

It has an aircraft-grade 5052 aluminum mounting bracket and locking pin that holds the dish at 0 degrees or extreme angles of 45(-45 or 45). 

Ubiquiti Universal Antenna Mount

Ubiquiti is renowned for its reliable aftermarket products. Their universal antenna mount is another accessory that works well with a Starlink dish.

Made from lightweight material, this J mount is easy to install in calm weather areas. It’ll give you an 18-inch reach and enough roof to improve your Starlink’s mounting angle. 

The mount’s 1.5-inch diameter will fit the Starlink mast with some tightening using the included U-bolts.

 However, you can use tape to fill the gap if there is wiggle room between the Starlink mast and the Ubiquiti J mount. 

How To Install The J mount

We recommend installing the mount where you confirmed the Starlink dish gets a stable connection.

  1. Use a level to mark out a straight line of the selected surface. We recommend installing it on your roof only as a last resort. Mount the J mount on eaves or wall sidings.
  2. Depending on the surface, pick the attachment hardware. (wood lag screws for wood, metal nails for brick surfaces)
  3. Place the J mount on the level’s demarcation and mark the drill points. 
  4. Drill the holes depending on the lag screw or metal nail sizes. 
  5. Use the level again to mark a straight level vertical line. 
  6. Screw or drill the mount in its vertical position and ensure it’s secure. 
  1. Unplug your dishy from the power source and other connections. 
  2. Pass the cable first through the J mount such that the bottom side of the mast can enter the mount. Alternatively, leave the cable out and slide the Starlink mast to the mount. 
  3. Secure the dishy into the mount with U-bolts or drill. Ensure the mast’s cable isn’t sitting on the mount. Leave space between the mount and where the dish’s mast attaches to the cable. 
  4. Secure the mount to the mast with your U-bolts. The tighter you fasten the U-bolts, the more secure your mast will be inside the mount. 
  5. If you didn’t pass the cable through the mount, ensure you secure the cable to the mount’s side with zip ties. 
  6. Secure the Starlink cable with clips to prevent damage.

Note: If you are drilling the mount, make sure you drill a hole large enough to fit the Starlink spring tab. Cover the drilled area with electrical tape to prevent water infiltration. 

As mentioned, the Starlink dish might not fit perfectly in the J-mount.

Plus, you must secure the dish to the mount to maintain the dish’s position during rough weather. 

Use these three accessories. 


Steel U-bolts with adapter brackets 

Steel U-bolts with adapter brackets 

Most J mounts will come with U-bolts as extras. U-bolts are the least invasive securing tools for J mounts. Simply attach the U end where the mast fits into the U-bolt. 

Align with the u-bolt’s bracket and fasten the nuts. 

It will not dent your mount or mast, and you might not mess up your Starlink dish warranty.

Universal Mount Adapters

Mount adapters work well in U-bolts to secure the mast to the J mount.

 Since they are not included in any aftermarket J mount package, you must get them separately.


Lastly, Drilling might be invasive, but it secures the Starlink mast to the J mount. The only downside is it might void your hardware’s warranty.

You can drill and secure the equipment using bolts, nuts, and washers.

Alternatively, drill accurate holes that align perfectly with the Starlink dish spring tabs. 

There’s a wide array of mounts for Starlink. The J Mount is arguably one of the most reliable.

 It’s affordable, sturdy, and fits both generations of the Starlink dish with minimal alterations. OEM Starlink J mounts take a long to get. 

Therefore, aftermarket J mounts are a superb alternative. Should you get one for Starlink? Absolutely. 

Use our guide to install.